IPB
Truck Camper Parts

Welcome Guest ( Log In | Register )

 
Reply to this topicStart new topicStart Poll

Outline · [ Standard ] · Linear+

> Problem, Electric Jackes, Problem, Electric Jackes

buck44
post Apr 29 2007, 05:02 PM
Post #1





Group: Members
Posts: 2
Joined: 27-April 07
Member No.: 622
Favorite Truck Camper(s): Lance
Type and Brand of Truck(s) Owned: F-250 4x4
Type of Tiedowns used: Home made frame mount with Fastguns
Truck and Camper Setup: F-250: Air bags, home made frame mounts with Fastguns, Lance 835 with 110 Watt solor panel.



Hello Everyone,
We are having an ongoing problem with the electric jacks on our Lance camper.
Example, when using the button to extend or retract all jacks, all
jacks may initially move but one will stop and the others sometimes
pulsate. Its not always the same jack that stops. When using the
individual buttons, one will always stop functioning before the camper
is loaded or unloaded. Have gone through the problem-solving checklist
that came with the camper with no results. Have any of you experienced
a problem with the electric jacks? Any information you may have will be
greatly appreciated.

Regards :(
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Rodg
post Apr 29 2007, 10:51 PM
Post #2





Group: Members
Posts: 9
Joined: 18-March 07
Member No.: 490
Favorite Truck Camper(s): homebuilt
Type and Brand of Truck(s) Owned: dodge 2500 xtcab diesel
Type of Tiedowns used: stablelift system
Truck and Camper Setup: in process of building truck camper from Glen-L plans that i got off web site. Alcapulco model, almost finished, have it skinned and still working on it. hope to be finished in 6 wks and on the road just in time for the spring trout run in Galveston, Texas



Rodg here, sounds like you have an electical problem. first ck your positive and negative connections to your battery. take the wires off the battery, clean the terminals with a wire brush. reconnect and see if that works. also ck the voltage out put on your battery. you might just have a battery going down and you are not getting enough juice to the motors. i would clean the terminals, if that didn't work i would try another battery. what you describe, alternating problems with more than one jack usually means a power supply problem, half dead battery would be my guess or dirty battery terminal connection. you need to get a full 12 volts to the motors, an ohm meter can check that also. if it is not the battery connection or the battery then you are going to have to ck and see if you are getting a full 12 volts to each motor with the ohm meter. if not, you must have a lose connection some where or a wire that has rubbed up against something and is shorting out.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
jegssr
post May 20 2007, 01:42 PM
Post #3





Group: Members
Posts: 3
Joined: 4-May 07
Member No.: 649
Favorite Truck Camper(s): northwood
Type and Brand of Truck(s) Owned: 03 Dodge dually Cummins 4WDquad cab
Type of Tiedowns used: custom
Truck and Camper Setup: 03 Cummins, 02 Arctic Fox slider, custom hitches and custom tiedowns



My Happijac instructions say that they are programmed to shut off after extended operation to ensure that they are not being operated accidentally.. Hold the "all up" button and the "all down" utton at the same time to rset the controller.
QUOTE(buck44 @ Apr 29 2007, 10:02 PM)
Hello Everyone,
    We are having an ongoing problem with the electric jacks on our Lance camper.
Example, when using the button to extend or retract all jacks, all
jacks may initially move but one will stop and the others sometimes
pulsate. Its not always the same jack that stops. When using the
individual buttons, one will always stop functioning before the camper
is loaded or unloaded. Have gone through the problem-solving checklist
that came with the camper with no results. Have any of you experienced
a problem with the electric jacks? Any information you may have will be
greatly appreciated.

Regards sad.gif
*

User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Todd Tumbleston
post Aug 12 2007, 05:20 PM
Post #4





Group: Members
Posts: 3
Joined: 14-February 07
From: Oroville, Washington
Member No.: 385



Hey, mine does it too depending on where i'm standing..... I thought the battery in the controller may be going but I haven't changed it yet... If i'm standing at the back door "open" or alongside, it works fine.... Otherwise it's on and off and on and off and on and off and it's only on all up or all down......

Todd Tumbleston 1030 lance superduty 250 cool.gif


--------------------
03 FORD Superduty/01 Lance 1030 with Firestone air bags on rear
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
buck44
post Aug 29 2007, 10:37 AM
Post #5





Group: Members
Posts: 2
Joined: 27-April 07
Member No.: 622
Favorite Truck Camper(s): Lance
Type and Brand of Truck(s) Owned: F-250 4x4
Type of Tiedowns used: Home made frame mount with Fastguns
Truck and Camper Setup: F-250: Air bags, home made frame mounts with Fastguns, Lance 835 with 110 Watt solor panel.



QUOTE(buck44 @ Aug 29 2007, 08:34 AM)
*



Hello Todd, Thanks for your reply on the electric jacks. I found the wire terminals for the electric jacks were loose on the control panel. After tightening them, three of the four jacks work fine. I am going to solder all connections to eliminate the possibility a poor contact due to oxidation.
I noticed you have air bags on your truck. How much air pressure do you use when you have your camper on the truck??
User is offlineProfile CardPM
Go to the top of the page
+Quote Post

Reply to this topicTopic OptionsStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
 

Lo-Fi Version Time is now: 28th March 2024 - 08:09 AM